China supplier palm oil processing plant in malaysia

China supplier palm oil processing plant in malaysia

We have made 40t/h and 80t/h palm oil mill machine for Indonesia,and we have cooperate

with Sinar Mas Group in Indonesia,hope you can visit those project if you want.

Palm oil production main process:

1. After transport the FFB to palm oil mill ,the fruits will go to stelizer by conveyor or palm fruit

cage.

2. After seperate palm fruits and palm bunch by thresher,Palm fruits will be conveyed to palm oil

pressers to get CPO.Palm bunch can be used as fetilizer or fuel.

3. After pressing,we can get palm cake and palm nut.Palm nuts will be conveyed to palm recovery

system to get palm kernels,fiber,palm shell.Palm cake will be conveyed to boiler roon as well.

4. After filtering,centrifuging,vacuum drying ,we can get crude palm oil (CPO),The CPO can be

sold directly or use for futher processing.

5. The sewage from all the plant will be processed by sewage treatment to reach discharge

standard.Sludge can be used for fertilizer in palm plantation.All the process cycle features with

short operation cyclye ,high automaticity,energy conservation and environment protection.

Reception of palm oil mill:

The FFB bunch be transported to plant by truck, after be weighted by weighting bridge,

the FFB will be loaded down to FFB Loading Ramp.

Loading Ramp:

Sterilization of palm oil mill:

1.By Scraper Conveyor, FFB be transported to the top of sterilizing tank.

Falling into sterilizing tank from feed inlet.

2. Sterilizing tank: Adopt vertical type sterilizer, WeLDd up by Q235B material

(Chemical composition:C 0.12~0.2%,Si 0.12~0.3%,Mm 0.3~0.7%,P

S

3. After FFB be transported into sterilizing tank (202), close the inlet of sterilizing tank,

and open the vent valve behind the

tank, saturating steam, which pressure is 3bar and temperature is around 130℃. After

all cool air been discharged out,

close vent valve, proceed to sterilizing section. Sterilizing time is 55~120minutes.

4. The sterilizing time also should be depend on the kind and quality of FFB, if the

pressure is too high or the time is too long, palm fruit will be rot, also Resulting

in the loss of oil, high temperature can change palm color.

5. Finish sterilizing process, close the steam valve, open the valve lead to Blow-off/down

Silencer. Open the sterilizing tank door(FFB outlet) after discharges out all

steam and water.

6. Open the sterilizing tank door(outlet), sterilized FFB will fall on the FFB Scraper conveyor.

Be transported to next station.

Threshing of palm oil mill:

Separate the fruit from the bunch through strong vibrating.

1.The sterilized FFB will be transport to thresher platform by scraper conveyor.

2.We adopt advanced Drum type thresher, insider diameter is φ1800mm, length is 5000mm.

The material of main shaft is #45 steel (main chemical composition is C0.42~0.50%, Si0.17~0.37%,

Mm0.50~0.30%, P≤0.035%, S≤0.035%, Cr≤0.25%, Ni≤0.25%, Cu≤0.025%).

3.Sterilized FFB be twisted and knocked in thresher. Palm fruit will be separated from empty bunch

totally, fall on Fruit Scraper conveyor though fence, the empty bunch will be transported to Bunch

Temporary tank by Bunch Scraper conveyor.

Digesting of palm mill:

Pressing station:

1. The palm fruit is transported to Crush tank by fruit elevator.

2.The fruit in crush tank will be heated to 90~95℃(by indirect steam), crush time is

10~20 minutes.

3.The pounded fruit flow into Palm fruit oil presse to press. Oil press cone can control

cylinder, working pressure is 50~70bar, revolving speed of presser main shaft is

12.5 r/min. Meanwhile the mixture of crude palm oil and water outflow from barrel

holes. Crude oil will be flow in Temporary Storage oil tank through crude oil groove.

Then oil will be pumped to Screening filter by oil pump. After filtering remove the oil

foam, deposit impurities. Palm oil flow into Passivating oil tank. The fiber cake and

nuts are exhausted from clearance of cone head drop on Breaking cake auger .

4. Palm fruit oil presser , the material of main shaft is 40Cr steel, (Chemical component:

C 0.37~0.44%,Si 0.17~0.37%,Mn 0.50~0.80%,Cr 0.80~1.10%) have been thermal refining,

the material of worm and cone head is 45# Cast-Steel, and the surface have quenching

treatment.

1. After removing the fiber and oil residue by Screening filter, palm crude oil flow

into Passivating oil tank.

2. The passivating oil tank will be inlet indirect steam and directly steam, after passivation

treatment palm oil and water mixture will be pumped to High level tank by Chemical

centrifugal pump, then flow into Clarifying tank stably.

3. There is steam pipe coil in clarifying tank, which can make water oil dilution ratio

stable, and separate water from mixture. And there is oil and sewage outlet, in case the

oil flowing will be short circuit, keep oil temperature around 100℃. After remove sludge

by filter, the water will return clarification tank to keep the water and oil ratio. The

waste water be discharged by another drain-pipe, which with special structure.

4. Clarified oil flow into storage oil tank from discharge hole of clarification tank , after

Disc-type separator remove moisture in the oil, then though Plate heat exchanger

heating to 105℃, remove residual moisture out from oil by Vacuum drier.

5. Vacuum degree of vacuum drying is achieved by Vacuum pump . The power of

vacuum pump is 5.5kw, adiabaticpressure is 23mmHg, the maximum capacity of

exhaust is 120m3/h.

6. The oil have been dried pumped to pure oil tank by Shielding pumps .

7. When the oil temperature in pure oil tank is about 50℃, oil will be pumped to produced

oil tank by gear oil pump.

Tricanter:

Desanding Tank:

1. Who is LD?

a. Leading manufacturer of edible oil mechanical equipment.

b. Factory with more than 30 years manufacturing experience.

c. School-enterprise partner of LD Technology University .

2. What can LD do for you?

a. 5-2000T per day oil seeds press production line.

b. 10-1000T per day solvent extraction production line.

c. 1-600T per day edible oil refinery production line.

3. Where have LD exported to ?

a. Europe:Serbia,Romania.

b. America:Peru,Paraguay,America.

c. Africa:Egypt,Nigeria,Cameroon,Ghana,Malawi,Burkina faso.

d.Asia:Indonesia,Kazakhstan,Russia,Thailand,Ukrain,Bangladesh,Uzbekistan,Pakistan.

Oil refining means separating impurity from oil based on the different characteristics of oil and impurity, in order to enhance the stability and security of oil. Oil refining including two technologies, physical refining and chemical refining.echnological process details of China supplier palm oil processing plant in malaysia:
AAA1

1. Acid reaction process
Oil temperature can be adjusted by screw plate heat exchanger. When the temperature is heated to about 80℃, mixing about 85% food grade phosphoric acid into acid reaction tank for reacting. In the tank, most non-hydrated phospholipid transfer into hydrated phospholipid.
AAA1

2. Neutralization process
In the neutral section, degummed oil with appropriate temperature and the appropriate concentration of alkali liquor, into the neutralization centrifugal mixer mixing, in order to achieve the effect of mixed, the mixture is then sent to neutralization tank for enough time, in this process, excessive alkali neutralization of free fatty acids and some phosphate form soapstock , after pumping oil soap mixture into heater oil heating to 85 ~ 90 ℃ in centrifuge separation oil - soap (or oil - glue). Oil soapstock of the separated (or foot) feet into the oil tank, and then to the salting out with soap pump tank isolated part of the oil.
AAA2

3. Washing process
Neutral oil from separator, still contains about 500 ppm soap, in order to reduce the residual content of soap, oil is joined by about 10% of hot water, washed in the washing mixer, hot water will absorb oil soap and other impurities, then in the water separator are separated.

AAA3

If you have any demand about microwave drying equipment and edible oil refining equipment, pls feel free contact us any time.

LD Miss Candy
Skype: leaderfoodmachine9
Mobile: +86 18363700691 (Also WhatsApp & Wechat)
Email: [email protected]

Shandong Leader Machinery Co.,ltd. is a microwave equipment, microwave drying sterilization machine, microwave heating equipment, microwave drying machine, microwave sterilization equipment, microwave drying equipment, whole s microwave curing equipment, microwave drying sterilization condiment, Shandong microwave drying Machine, melon seeds microwave dryer and other products specializing in the production and processing company, has a complete and scientific quality management system. Shandong Leader Machinery Co.,ltd.integrity, strength and quality of products recognized by the industry.

Why do you choose the Shandong Leader Machinery Co.,ltd. China supplier palm oil processing plant in malaysia?
1.Healthy! Pure mechanical squeezing craft maximally keeps the nutrients of the oil plants.No chemical substances left
2. High working efficiency! Due to a high working efficiency of the screw oil press machinery,both time and power can be saved.
3. Long durability! All the parts are made of the most suitable material and treated with refined crafts, such as cemented quenching and tempering to increase the hardness, consequently the durability.
4. China supplier palm oil processing plant in malaysiaCost-effective! Low investment! The wearing parts on the oil press machinery such as the squeeze loop, squeeze spiral and squeeze bar are designed to be dismountable. When they are out of service period, users only need to replace them and there is no need to displace the whole machine.

Shandong Leader Machinery Co.,Ltd.
Tel:+86 0531 85064681
Fax:+ 86 0531 85064682
Skype： taishan0072
What’sApp:+86 18905316466
Email: [email protected]

Address: No. 225, Huangqiao Village, Beiyuan, Tianqiao District, Jinan, Shandong, China

At Shandong Leader Machinery Co.,Ltd, we have one single goal in mind: to make you a satisfied customer. That single focus, driven from every aspect of the company's operation, is the key to our ongoing success. If you're a satisfied customer, you'll come back to us when you have additional Machine needs in the future, and you'll tell your friends about us. Then if we can make them satisfied customers, the cycle continues.

——————————————————————Wendy Yao Director